Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser for CAN bus. It is discreet and does not have LED indicators or key fobs, and is concealed in the wiring of your vehicle.
It also allows the user to turn off the system temporarily through Transport Mode to use it when they are renting out their vehicle. This guide will guide you through the process of installing the Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle from hacking, key cloning and relay attacks. The system connects directly to your car's ECU and is protected by a unique pin code that you can choose. It's undetectable to thieves using scanners for diagnostics or other modern methods, and is not able to be disabled by circuit cuts.
The system is simple to use, but professional installation is recommended to ensure a smooth connection to the ECU of your vehicle. A certified installer from Thatcham can assist with the installation and programming of your Ghost system. They can also suggest a tracking or alarm system to complete the security package for your vehicle.
First, the installer must disconnect your battery in order to avoid the possibility of airbag deployment and short circuits. After this is completed the installer is now able to begin work. Hand tools are the most basic to be used to make precise connections. A multimeter can be used to test electrical values. Cable tie and insulation tape are crucial to ensure connections are secure and keep wiring tidy. The Ghost Immobiliser user manual will provide specific instructions specifically tailored to your specific model.
ghost vehicle immobiliser is important to choose the right grounding spot that is free of dirt or paint during installation. The installer must be sure that the immobiliser's CAN H as well as CAN L wires are connected to the correct ports on your vehicle's ECU. These wires can be plugged in or soldered, depending on the model. Using a high-quality connector is recommended to ensure a sturdy and reliable connection.
Transport Mode can be turned on by the customer once the installation is complete. This permits mechanics or valet parking to use the vehicle, without knowing the pin code. The user must press the service icon on the dashboard five times in 2 seconds. The system will confirm this by showing five indicators.
The Autowatch Ghost 2 immobiliser is TASSA certified and is an extremely efficient immobiliser. It's a great choice for those who rent their vehicles regularly through platforms like Turo. Having an immobiliser can also reduce insurance premiums, since it greatly reduces the chance of theft.
Getting Started
If you're seeking a solution to safeguard your vehicle from theft it is best to go with an autowatch ghost immobiliser. The device stops your car from starting when someone copies or steals your key. This is due to its high-tech technology, which is designed to stop the engine from starting without the correct PIN code is entered.
The device works by connecting to the CAN bus network of your vehicle and allowing it to communicate with the ECU directly. It uses existing buttons on the dashboard and wheel to create a unique sequence only you can identify which makes it impossible for anyone else to start your car. This is the best security system that protects your car's pride and joy, keeping its value intact should you decide to sell it in the future.
Installing an immobiliser from Ghost is simple, but you must follow the directions to avoid electrical problems and system malfunctions. You'll need to locate a 12V power supply and a good grounding on the chassis of your car. Then, you can start connecting the wires to the immobiliser. Make use of high-quality connectors and soldering techniques for a secure connection. Connect the connections with heat shrink tubing, insulation tape or other materials to prevent short circuits in electrical power.
Once the wires are connected, you can connect the battery and turn on the engine to test the immobiliser's function. After ghost vehicle immobiliser 've confirmed that everything is functioning properly then you can put the immobiliser in a safe position inside the vehicle. Be sure to hide it securely to ensure that thieves cannot alter it.
The Ghost 2 immobiliser is TASSA (Tracker and Aftermarket Security System Association) verified This means it complies with the highest standards of security and is a great protection against car thieves. It is invulnerable to key cloning and hacking and cannot be disabled without the code. It is also simple to use and can be put into the service valet mode to ensure that your car isn't activated if you bring it in for service or an MOT.
Wiring
The Ghost Immobiliser, a cutting technological security system, has been designed to stop theft of vehicles. It communicates with your vehicle's ECU and connects directly to the CAN bus. Contrary to other aftermarket systems which require the removal of circuit components The Ghost Immobiliser does not interfere with the factory settings for your vehicle.
It's also undetectable to thieves using diagnostic scanning devices. The system does not send or receive radio frequency signals and instead uses CAN data for communication with your ECU. It doesn't even require any modifications to your existing key fobs.
Enter your sequence for disarming (either two or one buttons) and then switch on the ignition of your vehicle to use Ghost Immobiliser. The indicator will flash twice to verify that you've entered the correct code. After this, you can start your car and drive away with peace of mind.
Once installed, the Ghost Immobiliser will safeguard your vehicle from key cloning and hacking and will also protect the value of your most prized possession. In Transport Mode you can temporarily disable the Ghost Immobiliser when you need to give your vehicle to service or valet park.
To complete the Ghost Immobiliser installation, you'll need identify the source of power that is constant (12V) and an earthing point. Be sure that they are well-insulated and safe to touch. Cable ties are also suggested to secure the wires. This reduces the risk of theft by potential thieves. Be sure to double-check the location of these points to avoid making mistakes, and mark them with a piece of tape or label. Verify all connections for signs they're getting worn out. Make sure that all connections are firmly in place and properly protected. Finally, don't forget to test the Ghost Immobiliser after the installation is complete. This will make sure that the unit is functioning properly and that all connections are safe and well-insulated. If you encounter any issues, you must be sure to resolve them immediately.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that connects seamlessly with your vehicle's ECU to stop unauthorised motor starting. Its cutting-edge technology protects your vehicle from hacking and key cloning as well as other methods commonly employed by thieves to steal cars. The Ghost also works in conjunction with other alarm and tracking systems to give the most complete protection for your vehicle. The Ghost's unmatched features, paired with its subtle design makes it a preferred choice for car enthusiasts as well as security-conscious drivers.
To ensure the proper integration of the Ghost Immobiliser, you must to follow the steps of the installation process. A good starting point is to consult the wiring diagram of your vehicle that will serve as a roadmap for locating and connecting the wires required. Then, you'll need to determine the power source and grounding points. Once you have located them, you'll need to mark the points to make them easily identifiable when installing. It is also important to use top-quality tools and materials. Basic hand tools can aid in making precise connections. A multimeter can verify electrical values, and also ensure security. Insulation tape and cable ties will keep the connections neat and tidy. A Ghost-specific user's manual is also available.
It is important to test the system prior to installing it. Enter the PIN code into the system, and then start the vehicle. This will ensure that the immobiliser is working as it should and prevent unauthorised vehicle starts. This step should be done regularly as part your regular inspections of the vehicle to ensure that the system is working properly.
Once the installation has been completed, you can start driving your vehicle with confidence. The Ghost will protect your vehicle from thieves who might steal your car. It will ensure that no one will escape with your car if they do not have the correct PIN code. The Ghost can be paired with an approved Thatcham tracker, which detects attempts to steal or tamper with. This lets you track your vehicle if it is stolen.
The Ghost can be utilized on a variety of vehicles and is compatible with most major manufacturers. Monty's Locksmith can help you secure your vehicle with this innovative device. Contact us today to find out more about our service and installation options. We are a TASSA Registered installer which guarantees that we follow strict standards and procedures for installing our products. This guarantees customers, insurance companies, and law enforcement agencies that installations are done safely and properly.