Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket immobiliser that works with CAN buses. It's discreet It does not include LED indicators or key fobs, and is concealed in the wiring of the vehicle.
The user can also disable the system for a short period of time by using Transport Mode when renting out their car. This guide will walk you through the process of installing an Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle against hacking, key cloning and relay attacks. The system links directly to your car's ECU and is protected by a unique PIN code that you can choose. It's undetectable to thieves using diagnostic scanners or other advanced methods, and it is unable to be disabled by circuit cuts.
The system is simple to use, however it's essential to use a an expert installation to ensure a smooth and secure connection to your vehicle's ECU. A certified installer from Thatcham can assist in the installation and programming of your Ghost system. They can also recommend a tracking system or alarm to complement your vehicle's security package.
To avoid the accidental deployment of short circuits or airbags, the installer must first disconnect your battery. Once the battery is disconnected, the installer may be able to work safely. Hand tools are the most basic to be used to ensure precise connections. A multimeter is useful to check electrical values. Insulation tape and cable tie are vital to secure connections and keep wiring neat. Lastly, the user manual offers specific instructions specific to the Ghost Immobiliser model you have.
It is crucial to select the right grounding spot that is free of paint or debris during installation. Installers should also make sure that the immobiliser's wires CAN H and CAN L are connected to the proper ECU ports. Based on the model, these wires may need to be soldered or plugged in. A quality connector is recommended to ensure a sturdy and secure connection.
Transport Mode can be activated by the customer after the installation is completed. This allows valet parking or mechanics to access the vehicle without knowing the pin code. The user must press the service icon on the dashboard five times over two seconds. Once this is done, the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 immobiliser is TASSA approved and a highly efficient immobiliser. It's a great choice for those who rent out their vehicles regularly on platforms like Turo. An immobiliser can reduce insurance costs, since it reduces the risk of theft.
Getting Started
If you are looking for a solution that will secure your vehicle from thieves, you can't go wrong with an autowatch ghost immobiliser. It will stop your car from starting even if a criminal steals or copies the key. This is due to its sophisticated technology that is designed to prevent the car's engine from starting unless the correct PIN code is entered.
The device connects to the CAN bus network in your vehicle and allowing it to communicate with the ECU directly. It uses the buttons on your steering wheel and dashboard to create a unique sequence, that only you can understand. This makes it impossible for anyone else to start your vehicle. This is the best security system that will safeguard your pride and joy, keeping its value intact should you decide to sell it in the future.
Installing a ghost immobiliser is a simple process, but it's important to follow the instructions carefully to avoid issues with electricity and system malfunctions. First, you have to find and locate a permanent 12V power source and a good grounding point on the chassis of your vehicle. After that, you are able to begin connecting the wires that will be used to activate the immobiliser. Make use of high-quality connectors and soldering methods to create an effective connection. Insulate the connections using heat shrink tubing, insulation tape or other materials to avoid electrical short circuits.
Once the wires are connected, you can connect the battery and begin the engine to check if the immobiliser is working. If everything is functioning properly you can place it in a secure location under the dash or somewhere else in the vehicle. Be sure to hide it securely so that a thief cannot get it into a compromising position.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) that means it is a high-quality deterrent for car thieves. It is impervious to key cloning and hacking and cannot be disabled without the code. The device is simple to use, and can be set to the service valet setting to ensure that your vehicle will not be activated if you bring it to an MOT or for servicing.
Wiring
The Ghost Immobiliser is a cutting-edge security system specifically designed to deter theft of vehicles. It communicates with your vehicle's ECU and connects directly to its CAN bus. Unlike other aftermarket systems that require the removal of circuit components, the Ghost Immobiliser doesn't interfere with any of the factory settings of your vehicle.
It's also completely undetectable to thieves using diagnostic scanning devices. This is because the system doesn't send and receive radio frequency signals and it utilizes CAN data to communicate with your ECU. Additionally, it doesn't require any modifications to your vehicle's existing key fobs.
To make use of the Ghost Immobiliser simply switch on the ignition in your car and enter your disarm sequence (either one or two buttons). The indicator will flash twice to confirm that you have entered the correct code. Now you can begin driving your car safely.
Once installed, the Ghost Immobiliser guards your vehicle from hacking or key cloning, while protecting its value. If you have to hand over your vehicle to valet parking or for service The Ghost Immobiliser will be temporarily disabled in Transport Mode.
To complete a Ghost Immobiliser installation, you'll need identify the source of power that is constant (12V) and a grounding point. Ensure that these are both well-insulated and safe to touch. It's also recommended to use cable ties to bundle and secure the wires, since this will decrease the chance of tampering by potential thieves. To avoid making mistakes, double-check these points and mark them with labels or tape. Verify every connection for signs that they are wearing out. Make sure that all connections are securely in place and properly insulated. Also, don't forget test the Ghost Immobiliser after the installation is completed. This will ensure that the unit functions properly and that all connections and insulation are secure. If you encounter any issues, you must be sure to address them immediately.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that integrates seamlessly with your vehicle's ECU to prevent the motor from starting without authorization. Its cutting-edge technology protects your vehicle against hacking and key cloning along with other methods commonly used by thieves to steal cars. The Ghost is also able to work in conjunction with existing alarm and tracking systems to provide the best protection for your vehicle. The Ghost's unparalleled features and secluded design make it a preferred option for car enthusiasts and security-conscious drivers too.
In order to ensure that the Ghost Immobiliser is properly integrated the Ghost Immobiliser, it's important to follow every step of the installation process. The best place to start is to consult the wiring diagram of your vehicle, which will serve as a guideline for locating and connecting the necessary wires. You'll then need to identify the grounding and power sources. Once you've found them, you'll be required to mark them so that they're easy to identify during the installation process. It is essential to use top-quality materials and tools. Hand tools are essential to assist you in making precise connections. A multimeter can verify electrical values and guarantee security. Insulation tape and cable ties can help keep connections tidy and neat. Finally, a user manual will provide specific guidance specific to your Ghost model.
It is essential to test the system prior installing it. Enter the PIN code into the system, and then start the vehicle. This step will confirm that the immobiliser functions as intended, preventing unauthorised vehicle starts. It's recommended to perform this procedure regularly as part of your regular inspections of the vehicle to ensure the system is operating properly.
After the installation is completed, you can start driving your car with confidence. The Ghost will safeguard your pride and joy from would-be car thieves. It will ensure that no one can take your car away if they do not have the correct PIN code. The Ghost can be used in conjunction with an approved Thatcham tracker that detects any attempts at theft or tampering. This allows you to track your car in the event that it's stolen.
The Ghost is compatible with a variety of vehicles, including those made by the majority of major manufacturers. If ghost immobiliser birmingham interested in protecting your car using this advanced device, call Monty's Locksmith today to find out more about our installation and maintenance options. We are a TASSA Installer who is registered which guarantees that we adhere to the strictest guidelines and procedures for installing our products. This guarantees customers, insurance companies, and law enforcement agencies that all installations are done safely and in a safe manner.